HANNOVER MESSE 2018, 23 - 27 April
Homepage>Exhibitors & Products >M-Tech®P Edge bonded shims (spacers), Loose leaf shims

M-Tech®P Edge bonded shims (spacers), Loose leaf shims

Georg Martin

Exhibitor details
Logo M-Tech®P Edge bonded shims (spacers), Loose leaf shims

Exhibition stand

Hall 22, Stand D28

Product description

Edge bonded shims or loose leaf shims M-Tech®P (Lamipac) compensate tolerances in a rapid and targeted manner.

The following benefits can be exploited when using M-Tech®P edge bonded shims
- Large component part tolerances can be compensated for precisely and rapidly in a few steps by using both thick and thin metal shims.
- Various materials can be used to recognize the thickness or reduce corrosion.
- The sealing requirements of the adjustment element can be met by bonding.

Handling is easier if adhesive is only applied at a few points around the circumference of the shim or only on one side, much in the same manner as a tear-off calendar. Shim packages can be bundled at a lower price as "loose leaf shims" instead of gluing them around the circumference.

M-Tech®P spacer products can be manufactured from brass, mild steel and stainless steel. In this case thin strips with a thickness of 0.025 mm upwards or sheets with a thickness of 3.00 mm are processed.

Product website

All products offered by this exhibitor

Protective ring for automobiles

For use in automobile propeller shafts to protect the universal joint. Low ductile punched part made of sheet steel. Material - Cold-rolled slit strip DC04, 1.0388 Processing; - Stamping - Forming - Testingread more

Large cap for ships' drive units

For use in the propeller shafts of ships' drive units to protect and hold the internal ball bearings of the universal joint and fasten the shock absorber of the propeller shaft. Highly ductile punched part made of sheet steel. Weight - 901.0 g Material - Cold-rolled slit strip, DC04, 1.0388 Processing; - more

Sealing cover for automobiles

For use in automobile propeller shafts to protect and hold the internal ball bearings of the universal joint and cover the propeller shaft. Highly ductile punched part made of sheet steel. - Weight - 748.50 g - Material - Cold-rolled slit strip DC04 - 1.0388 Processing; - Deep drawing - Stamping - more

Center wheel with cap for automobiles

For use in automobile propeller shafts to protect and centre the universal joint at the flange. Highly ductile punched parts made of steel sheet, pressed in and tacked with the heat-treated steel center wheel. Subsequent soldering and tempering. Weight - 285.69 g Material; - Cold-rolled slit strip DC04 more

Interior centering for automobiles

For use in the homokinetic ball joint of an automobile propeller shaft. Interior centering for automobiles is punched part made of 2.5 mm thick cementation steel. - Surface tolerance of the lower side Ra 0.8 µ. - Tolerance of the underside towards the middle of the dome-shaped cupola 0.02 mm. - Hardened more

Suction roll ring for sheet-fed offset printing presses

Used in the extension arm of sheet-fed offset printing presses. Complex connection part consisting of a housing (punched part) and plastic flange pressed in airtight. Punched part made of very highly ductile, rustproof steel strip. This means considerable weight saving compared to solid parts. Punched more

Sleeve for automobiles

For use in automobiles with hybrid drives. To cover and protect electrical plug connections. Punched part made of highly ductile rustproof steel strip. Area of application - Automotive industry Weight - 10.68 g Material - Rustproof steel strip 1.4301 Processing; - Deep drawing - Stamping - Forming - more

M-Tech®S extra-fine metal stamping parts, starting from 0.010 mm

With M-Tech® - Martin Technology, etched and laser-cut products can be replaced with precision stamping metal foils with simple geometry. As an economical alternative to chemical etching or laser fine-cutting, Georg Martin GmbH proposes product solutions with the lot sizes from 1 to 100,000 pieces more

Laminum® HP1 Laminated Shims

Tolerance compensation in the assembly of components can be optimized to 25 micrometres with the new, high-precision shim (Schichtblech) from Georg Martin GmbH that goes by the name of Laminum® HP1. The special feature of these stainless steel spacer shims is the combination of severable peelable foil more

Solid, massive spacer shims

Solid shims M-Tech®S makes it possible to adjust the finest tolerance graduations. A classic tolerance compensation product that we offer is a solid shim that we manufacture in accordance with clients drawings. Depending on the thickness selected M-Tech®S shims make it possible to make compensations more

Laminated spacer shims

Material specifications Laminum, M-Tech Lread more

Assemblies from stamped and formed parts with movable elements

Mechanical assemblies from stamped and sheet metal formed parts are beeing created to become precise functional elements. This is achieved by using additional processes like: chip removal, welding, adhesives, flame gunning, assembly, coating and heat treatment. These products fulfil precise mechanical more

M-Tech®F Metal foil tapes and blanks

Material specifications M-Tech F Metal foilsread more

Stored items


Server communication error: Item could not be saved.